나소텍
Nasotec
NewClassD
Jantzen, Denmark
CMC Audio
DIY Parts(A)
DIY Parts(B)
Audio Consulting
IntegrityHiFi
Yamamoto音響
AM Denmark
Clones Audio
Cardas
Connectors(단자)
Audio Cables
Analog기기/부품(중고)
Capacitors(콘덴서)
Dentec
Car Audio
L C Audio, Denmark
Volume control
Speaker Drivers
WBT
CD/LP
Dact/Dual Connect
Event / 장터(1)
Event / 장터(2)
For foreign orders
신상품
   
   
   
   
   
   
   
   
 
 
   
   
비밀번호 확인 닫기

> Dact/Dual Connect > 연장축 연결장치
연장축 연결장치


제조사 DACT, Denmark
상품코드 da0105
판매단위
판매가 28,000
주문수량
EA
재고 1개
바로 구입 장바구니에 담기 위시리스트에 넣기
 
     
상세 정보
Shaft-extensions
DACT logo

CT-ext1. Shaft extension kit.

DACTPurpose
Without the CT-ext1 extension kit, the attenuator and the input selector switch have to be mounted in the front panel of the equipment enclosure. The purpose of the CT-ext1 shaft extension kit is to allow mounting of the DACT CT1 or CT2 audio attenuators and/or the CT3 audio input selector switch at any location within the equipment enclosure. The recommended location of both attenuator and input selector switch is as near to the signal input/output sockets as possible. In this way, the signal cables may be shortened and the sonic degradation caused by the cables will be minimized.
At DACT we believe in using non-magnetic materials for audio equipment and CT-ext1 does not contain any magnetic parts. CT-ext1 consists of:
 - 1 pcs Extension Shaft. When ordering please specify CT-ext1/S for a kit with a short version of the
  shaft (200mm = 7.9 inch.) or CT-ext1/L for a kit with a long shaft (400mm = 15.7 inch.). Shaft material:
  Aluminium. 
 - 1 pcs Connection Link. Material: Brass. The connection link includes 4 pcs M3 stainless steel screws.

Extension shaft dimensions

 

Short version (CT-ext1/S)

Long version
(CT-ext1/L)

 

mm

inch.

mm

inch.

L1

200

7.9

400

15.7

L2

50

1.97

50

1.97

D1

6.5

0.256

6.5

0.256

D2

5.95

0.234

5.95

0.234


 - 1 pcs Front Panel Bearing Bush. Material: Brass. Includes
  1 pcs M10 stainless steel nut

Extension shaft, outline drawing. Material: Aluminium.



How to use CT-ext1
1. Mounting the Front Panel Bearing Bush. To mount the bush in the front panel requires a hole in the front panel of at least 10mm (0.395 inch.). Preferably, the hole should not be larger than 13mm (0.512 inch.). Fasten the bush using the supplied M10 stainless steel nut.
2. Mounting the Connection Link.
Please observe that the mounting holes in the two ends of the link are not of equal size. The smaller hole (6.05mm = 0.238 inch.) is for fitting the link to the shaft of CT1, CT2 or CT3. The other end (hole diameter 6.6mm = 0.260 inch.) is for fitting the aluminium extension shaft. Make sure to tighten all four screws properly.


 

















 



3. Fitting the Extension Shaft.
If the extension shaft is longer than required, it may be cut to the right length accordingly. PLEASE MAKE SURE always to cut the end of the shaft with the largest diameter. This end is to be fitted into the Connection Link, whose hole diameter will accept the diameter of the non-machined end of the shaft. Please observe that the shaft is designed to be used with a knob that has a 6.0mm hole (and not with a knob that has a 1/4” hole).

 

 

                 ORDERING INFORMATION

Part number

Description

CT-ext1/S

Shaft extension kit. Version with short extension shaft (200mm = 7.87”)

CT-ext1/L

Shaft extension kit. Version with long extension shaft (400mm = 15.75”)

 

 

 

사업자등록번호: 128-08-81985 / 통신판매업신고: 제2020-고양일산동-2196호 / 대표: 손동찬
주소: 경기도 고양시 일산동구 호수로430번길 58-13

Tel: 031-932-1730/ E-mail: nasotec@nasotec.com 개인정보취급방침

이메일주소 무단수집거부 / Copyright 1999-2005 by Nasotec Corporation